RFS HYDRAULICS/RFS 液压 RFS 黄铜 25MM OD X 25MM OD 90 度联合弯头压缩接头,重型系列 F-D-B-L-25S - Eezee
Shopping List
购物清单
CNY - ¥
Image
/
/
/
/
RFS HYDRAULICS/RFS 液压 RFS 黄铜 25MM OD X 25MM OD 90 度联合弯头压缩接头,重型系列 F-D-B-L-25S
RFS HYDRAULICS/RFS 液压 RFS 黄铜 25MM OD X 25MM OD 90 度联合弯头压缩接头,重型系列 F-D-B-L-25S
Image
Image
Image
Image
Image
Image
产品描述

Rfs Brass 25mm Od X 25mm Od 90 Degree Union Elbow Compression Fittings, Heavy Series F-D-B-L-25S

90D Union Elbow

Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree union elbow combines tubes together at a 90-degree angle. It is made of brass material with 2 compression ends. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system.

About 90D Union Elbow

Size : 6mm to 42mm
Series : L (Light Series) & S (Heavy Series)
Working Pressure (bar) : L series (160-315) & S series (315-496)
Material : Brass
Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1

DIN Fittings installation guidelines:

Step 1 : Cutting ring and nut to be placed over the tube in the correct direction.
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.


¥ 226.29
数量:
EA
This item is sold by
Image
SG-8088441545
来自 RFS Hydraulics 的 Pipe Elbow
寻找和比较同类产品
更多来自 Pipe Elbow
用更广泛的选择扩大您的搜索范围
Image
最佳