Shopping List
Shopping List
SGD - S$
Image
/
/
/
/
ORING JIS B2401 G40 ID 39.40 x CS 3.10 Viton Fluoroelastomers (FKM) 75 Shore
ORING JIS B2401 G40 ID 39.40 x CS 3.10 Viton Fluoroelastomers (FKM) 75 Shore
Image
Image
Image
Specifications
infotip-icon
View other O Ring dimensions or variations
Please select at least one specification below.
International Standard Size
JIS B2401
Reference No.
G40
Inner Diameter
39.4 mm
Outer Diameter
45.6 mm
Cross Section
3.1 mm
Material
Viton Fluoroelastomers (FKM)
Durometer
75 Shore
Minimum Operating Temperature
-15°C
Maximum Operating Temperature
199°C
Product Description

ORING JIS B2401 G40

ID 39.40 x CS 3.10

Material : Viton Fluoroelastomers (FKM) 75 Shore

Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.

This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).

In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings.

The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.

Temperature Range (Dry Heat)

Low: -5`F / -15`C High: 390`F / 199`C

Overview on Application Rating for Material Silicone

Properties (Rating)

Oils & Grease - Excellent

Tear Strength – Good

Fuel Resistance - Good

Heat Ozone & Aging Resistance - Excellent

Water Swell Resistance - Good

Ammonia, Amines, Alkalis - Poor

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.

Primary Usage

O-Rings and rubber seals are generally used for:

· Applications that require resistance to OIL

· Applications that are required to work in low temperatures (-0°C)

· High performance Fuel systems that requires strictly no leakage

  • Aircrafts
  • Marine Ships
  • F1 Cars

· General Industrial Use

Tips for installation of an O-ring

O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.

So how do you install an O-ring?

The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.

If you want to install an O-ring correctly and within a short time, here are steps to follow:

· Covering and lubricating the threading of the shaft

The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.

· Don’t force it over sharp corners

That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.

· Even stretching

You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.

· Don’t roll it down the shaft

Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.

· Finishing it off

Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.

For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.

Installation Guide

Highly Matched Items
View items that have the same or are a close match to the specifications of this item
O Ring from OEM
Source & compare similar products
More from O Ring
Expand your search with a wider selection
Recently Viewed Products
Compare & Refer to previously viewed items
Image
Top